New Jersey Auto Body Shop | Peotters Tire and Auto

Did You Know? Some of the biggest questions people run into deal with the repairing their vehicles in New Jersey.

Many times people are confused and don’t know how to go about picking the right New Jersey auto body shop.

What process should I run through in picking the right vehicle repair shop? What questions should I consider?

What value am I getting for my Summit Auto Body Repair?

The most important question in determining what auto body repair shops is: What value am I getting in repairing my vehicle here?

Peotter’s Tire and Auto wants to head a warning that possibly, some body shops out there are looking for unsuspecting customers and ways to pad their bottom dollar.

A lot of times a Summit Auto Body shop will offer the lowest price because they know this will attract customers.

Unfortunately, from a customer standpoint choosing the lowest price is not always the way to go.

Daniel T., Vice President of National Auto Parts, in Dallas, Texas, concurs that doing this will only create more car issues in the future.

“Repairing your vehicle is always about what you get in return.

These days, New Jersey body shops continue to push the limits of their customers to see how much more they can get away with. At this point the body shop knows exactly what they’re doing. Is the customer to know the better?”

What can I do to protect myself?

A solution that’s been picking up a lot of traction recently is hiring a third party to assist you in this area.

There are a few good car crash consultants out there that will help you figure out what’s being put on your vehicle and how the vehicle’s being repaired.

- Hey this is Donnie Smith.

This lesson, we're gonnatalk about dent repair.

Now before we just jumpon this car and start repairing this dent, it'simportant for any repair job to wash it good withsoap and water to remove all the contaminants,the waxes and greases.

We've already done that,we used a power washer to clean the car and now we're using a wax and grease remover.

And this is just toassure that all the waxes and greases, silicones,things like Armor Alls that may have been sprayedaround the vehicle are removed, 'cause this will eliminatemany of the paint problems that arise during a repair process.

This will also save onsandpaper cause it won't be loading the sandpaperwith these contaminants.

Now we have the repair areaclean and we can begin repairs.

But before we do, we wanna take a look at the damage and seewhat's wrong with it, see where the indirectdamage is and direct damage, and determine what repairmethods we're gonna use to repair this damage.

Now when thinking aboutdamage, it's a good idea to think about water.

Because you know if somethinghits water it goes down, and when it goes down italso pushes a wave up.

So you've got the low areaand you've got the high area.

Think of damage the sameway, because any time there's a dent there's gonna be a low and there's gonna be a high.

So whenever you look at thisdamage, you can see that the center part of the dent isof course the direct damage, but then if you look up here on the top, you can see the crown, oreyebrow some people call it.

And you can see that that is pushed up.

That whole top of the fenderis actually pushed up.

So if you tried justto pull out on the low, or push down on the highthat's not gonna work.

You've got to roll themetal, you've gotta push down on that high while you'repushing out on the low.

Now, when you go todetermining what repair method you're gonna use, you mayhave some different types of tools, you may havesome high dollar tools, a stud welder gun, otherdent repair systems.

Where really what you wanna think of is what is the easiest method? If it's a hammer and dolly,you have access to both sides, then use a hammer and dolly.

Just because you've got thehighest piece of equipment does not mean you haveto use it every time.

Now on this particularrepair, if you drop the liner, you are able to get to the back side.

So if you can get to the back side, this would definitely be acandidate for hammer and dolly.

Feeling back there to see ifthere's room to get a dolly, which I determined that there is.

Another thing to remember isthat whenever you're repairing a dent to reverse what happened.

You wanna work from the outside in.

First in, last out.

So whatever happened first in an accident, that's the last thing you wanna repair.

Also remember whenworking with thin metal, it's thin, and you may be able to move some of this with yourhand some of the times.

Doesn't work every time, butI'm gonna reach back there and keeping that in mind that I'm gonna push down on that high,out on the low area, use my hands to rough this out.

Now this ain't gonna be perfect, it's just to rough out the damage, to get the majority of the damage out.

I can see that there arestill some highs and lows, I can feel 'em.

I know it's hard to see on the video, and even if you're doingthis yourself it may be hard to see this sometimes, butI've got a trick that'll help you locate the lows.

If you get a block withsome 80 grit on it, you can cross sand the damaged area, and what this'll do is that the highs will immediately go to metal, of course, 'cause they're high,but the lows, you'll see it doesn't sand it at all, andthis will identify the lows.

Now you can see the twolow areas very easy.

Now using the dolly, I'mgoing to reach behind this panel with the dollyand I'm gonna push out on those low areas.

Also, while I'm pushing outI'm gonna have to remember where those high areas areso I can tap in on those.

Remember, we always wannawork in multiple directions.

Whatever tool you're using, just remember to push out on the lowsand in on the highs.

Also, when using adolly, there's different dollies, different shapes.

You want the shape of thedolly to fit the contour of the part you're working on.

If this dolly was completelyflat it wouldn't work well with this repair.

Okay, now I am working on getting my dolly located on the back of themetal where I want it to go.

It may take a little bitof time to get it exactly where you want it, but I wantit right on those low areas, so that I can raise the low areas out.

Also while I'm raising lowareas out, while I'm pushing on them with the dolly, I wannatap down on the high areas.

This will allow the lowareas to come out while the high areas are tapped in.

This is called the Hammeroff Dolly technique, because I'm not actuallyhammering on the dolly.

The dolly is pushing out on the low, the hammer's pushing in on the highs.

There is also a Hammer on Dolly, and that's where youare hitting the dolly.

Any time you hammer on dollythat stretches the metal.

You wanna save that for your final stages, until you get the metalcloser to where you want it.

Then you can do some hammer on dolly for your final straightening.

So I'm gonna do a little bitmore metal straightening, and then I'm gonna use the block sander with some 80 grit on it tocontinue blocking that out to identify my highs and lows and see how the progress is coming.

Now whenever you're blocksanding with 80 grit to identify highs andlows, it's always important to cross sand.

By sanding in just onedirection, you're not gonna find all the highs and lows.

And this goes for if you're doing this to identify highs and lows,or block sanding body filler.

Cross sanding always levels much better.

Now we're using this sander,and this basically takes the place of what we usedto use with thicker metals, which is a body file.

However a body file will actually shave the top layer of the metalwhich would help level it.

We don't wanna do thatwith thinner metals.

We wanna use methods thatdoes not remove any metal.

So any method that you canuse that does not remove metal is always gonna be a better choice with these thinner metals.

Now I'm feeling out thedamage with my hand, just seeing what all highsand lows that I feel.

A little tip for feeling damage, because you'll have to do that often, is to use the flat of your hand.

Often I see fingertipsused, but that is not gonna catch the highs and lows,you're gonna miss 'em.

So always use the flatof your hand to be able to feel the damage.

Another trick that sometechnicians use is to use a rag, they claim that they can feel it better, it kinda eliminatesthe different textures.

You put a rag over yourhand and go over the damage and see if you can feelthe highs and lows better.

Try both ways, whichever works best is the method for you to use.

Now I feel a little bit ofhigh, so here I identified a high, so I'm just gonna tap that down with the pick side of the hammer.

I'm just basicallylowering that high area.

Now I'm going to re-blockit, re-sand it with this 80 grit to make sure thatit did remove the high area.

I feel of it, and I feelthat that feels good.

It's not perfect, butwith these thin metals, if you try to get 'em just perfect, try to metal finish 'emlike they did older metals, you're gonna weaken and thin the metal.

You wanna get it within 1/4 of an inch.

Anywhere between 1/8 and 1/4 is what most body fillersuppliers recommend.

However, you don't wannaexceed 1/4 of an inch, that's maximum after sanded.

You don't wanna exceed that amount.

This dent is well underthat, it's probably within 1/8 of an inch.

I'm noticing there's stilla little bit of a crease down here so I need to work that out.

I'm gonna get a hammer and dolly in there, I'm gonna raise in on the low area and I'm gonna tap this crease area in so that we can roll this metal back to where it's supposed to be.

As I'm pushing out with the dolly, I'm tapping in on that high area.

Now I'm being real careful herenot to hit the bumper cover.

It'd've been a better idea if I went ahead and dropped the bumper cover.

I'll probably be blending into that.

Another trick you can do is put a couple layers of masking tape.

I should've did that, Ishould've put masking tape or went ahead and dropped the bumper.

Because the last thingyou wanna do is sand into an adjacent panel,especially if it's not one that you're blending and cause damage that you have to repair.

I'm still having problemswith the low area right here, so I'm working on that.

Now the problem with this area, it's a little harder to get to'cause there's a brace there.

I'm following the same techniques, I'm gonna push out on that low area and I'm tapping around the high areas.

When I hammer on dollyyou can hear that ping, it makes a different sound.

You can hammer on dolly someto help remove that damage, but again remember thatthat stretches the metal and try to reduce theamount that you do that.

Little bit of a high, I knocked that down.

Okay, I'm gonna use my block with 80 grit to sand the damaged area some more to see if I got thedamage worked out enough to apply the body filler.

And I sand it and I feelof it, and there's still too much of a low there.

So I'm going to need to goback in there one more time and use the dolly and hammer.

I'm going to use the pickbecause there's a high here.

I'm pushing out on thatlow and I'm going to hammer on dolly a little bit,and sand it one more time to see if that has it.

And that's what it takes, itjust takes doing a little bit, feeling of it, checking your progress until you have thedamage where you want it.

We got the metal straightenedwithin 1/4 of an inch, really within 1/8, but 1/4 after sanded is the maximum amount of filler that most body filler manufacturers recommend.

No more than 1/4 of an inch.

That's the maximum amount.

I know 3M, Evercoat, they all have that on their technical data sheets.

So anything more than 1/4 of an inch you really need tostraighten it more than that.

You need to get it straighter.

Again, with these thinnermetals you don't wanna try to work it and work it,because you're gonna work-harden the metal.

It'll become work-hardened, thin, brittle, it may even crack on you.

It's almost impossible toget these thinner metals to do the metal finishingtechniques like they used to do where they'd work the metaland file it down and get it just perfect, prime it.

Now there is one exceptionto that, and that's PDR.

Paintless Dent Repair.

That's a total different set of techniques than we went over in this video.

This video is straightening metal like a body shop would perform.

Again, remember dependingon the extent of damage, like a fender, that wouldreally go into consideration, do we wanna repair that or replace it? Now on 1/4 panel, thosepanels usually cost more.

And also, it's a weld onpanel, so it's gonna take a lot of labor to replace it.

So you can have a lotmore damage in 1/4 panel than you would a fender,and still repair it.

Many times in body shops and dealerships, if there's even a couple ofhours of damage on fenders, they just go ahead and replace them, which is R and R, Remove and Replace.

Anyway, I hope you learnedsomething this lesson.

Thanks for watching, we'llsee you in the next lesson.

When looking for a good car crash consultant selecting one that gives you a lot of insight on the repair and product being used is imperative.

Using these specialists provides visibility in an area with many questions.

Another way is looking for a detailed report of the work being put into the vehicle and reviewing the warranty the shops offers.

Collision Car Repair

When you get into an accident, every insurance gives you an assessment of the damages, take a look at the sheets and read over to see what product they’ve listed for use.

Auto Body Shops sporadically will attempt to use cheaper parts to make more money. Requesting the use of what’s listed on your insurance assessment is not unusual and will help protect against this.

In regards to warranties, most legitimate body shops will have an extensive warranty and stand by their work.

Where should I look for the body shop?

Driving to the nice plush auto body repair shops off the highway might be convenient, but doing this often drives up the price of the job. “All businesses have costs and are in it to make money.

With this assumption, you have to believe any cost a business incurs will be passed onto their consumer,” Daniel says.

Hanging off the highway, and looking more in-city gives any prospective client a better chance to keep labor costs low.

Prices per hour for labor can vary wildly from $30-$100 for the same type of work.

Don’t misunderstand the shop may not look the best, but you can be guaranteed going this route will provide good value.

Finding the Best Summit Auto Body is Just Around the Corner for those of You in New Jersey:

Best Auto Repair

>>> WELL, IF YOUR CAR IS EVER DAMAGED IN AN ACCIDENT OR REPAIRED THROUGH MAJOR INSURANCE COMPANY IN THIS COUNTRY, THERE ARE STATE AND FEDERAL LAWSUITS IN THIS COUNTRY YOU SHOULD KNOW ABOUT.

AUTO BODY SHOPS ACROSS THE COUNTRY, MORE THAN 500 OF THEM CLAIM SOME BIG INSURANCE COMPANIES LONG DELIBERATELY SKIMPED WHEN IT COMES TO REPAIR DAMAGED VEHICLES.

ALSO, THE INSURANCE COMPANIES CAN HAVE THEIR PROFITS.

THE LAWSUITS ALLEGE IT'S A SCHEME THAT CANNOT ONLY LEAD TO RUSHED AND MINIMAL REPAIRS BUT RECYCLED, REMANUFACTURED AND ONE LAWYER PUTS IT JUNKED PARTS TO FIX YOUR CAR.

ATTORNEY GENERAL BELIEVES THE ALLEGED SCHEME YOU COULD BE DRIVING A DANGEROUS CAR.

CNN SENIOR INVESTIGATIVE CORRESPONDENT DREW GRIFFIN REPORTS.

>> Reporter: TO SEE WHAT'S REALLY GOING ON, YOU'VE GOT TO DO SOMETHING YOU PROBABLY CAN'T DO AT HOME.

LIFT WHAT YOU THINK IS YOUR REPAIR CAR, GET OUT SOMETHING CALLED A BORROW SCOPE AND CHECK THE FRAME TO SEE IF THE AUTO BODY SHOP FIXED IT, WHAT YOUR INSURANCE COMPANY LIKELY RECOMMENDED.

>> THERE'S THE RIFF IN THE RAIL.

>> Reporter: BILL BURN, A NATIONAL AUTO REPAIR EXPERT TESTIFIES ABOUT BAD REPAIRS AND THIS, HE SAID, IS ONE OF THEM.

THE RESULT OF A SYSTEM DESIGNED TO SAVE MONEY FOR INSURANCE COMPANIES.

>> WHAT THEY DID WAS REPLACED THE NEW END CAP ON THERE AND THE END CAP COVERS THAT, SO THE CONSUMER WOULD NEVER SEE THIS.

IT IS UNSAFE.

>> AND YET THEY PUT IT BACK.

>> CORRECT.

>> Reporter: BURN IS NOW PART OF THE MAJOR LAWSUIT INVOLVING MORE THAN 500 AUTO BODY SHOPS IN 36 STATES.

ALL SUING DOZENS OF INSURANCE COMPANIES ACROSS THE COUNTRY.

THE SHOPS BELIEVE THE INSURANCE INDUSTRY IS INVOLVED IN A DELIBERATE SYSTEM TO SEND YOU AND YOUR CAR TO SHOPS THAT ARE PRESELECTED BY INSURERS TO DO THE ABSOLUTE BARE MINIMUM TO FIX IT.

EVEN TELLING BODY SHOPS TO USE USED OR RECYCLED PARTS BECAUSE THEY'RE CHEAPER.

MATT PARKER IS AN AUTO SHOP OWNER IN MONROE, LOUISIANA, WHO SAID HE SEES THE SAME PROBLEM.

HE SAID STATE FARM TOLD HIM TO USE A REMANUFACTURED HEADLIGHT IN A TOYOTA TACOMA.

THIS IS WHAT HE GOT.

>> IT'S GOT A HOLE IN IT HERE AND THEN YOU CAN SEE WHERE THEY SCREWED THIS BRACKET BACK ON THE VEHICLE.

NOW, YOU CAN SEE HERE WHERE ALL THESE PARTS WERE KNOCKED OFF AND GLUED BACK TOGETHER.

YOU CAN ALSO SEE HERE WHERE THE TOP CORNER AND THE LENS IS BUSTED AND THIS PART OF THE HEADLIGHT IS BROKEN.

THIS CAME OUT OF A BOX WRAPPED LIKE IT WAS SUPPOSED TO BE -- ABSOLUTELY, LIKE A NEW PART.

THE INSURANCE COMPANY WANTS US TO PUT THIS STUFF ON THE CAR.

IF WE REFUSE TO PUT IT ON THE CAR, THEN THEY LABEL US AS A SHOP NOT WILLING TO GO ALONG WITH THEIR PROGRAM AND THEN TRY TO STEER OUR BUSINESS AWAY FROM US.

>> Reporter: THIS IS WHY HE AND THE OTHER SHOPS RETAINED JOHN ARTHUR EVES TO SUE.

>> EVERY STATE IN THE UNION IS EXPERIENCING THE SAME SORT OF STRUGGLE HERE BETWEEN THE BODY SHOPS TRYING TO DO AND INSURANCE COMPANY TRYING TO USE UNSAFE PARTS AND METHODS ON THEIR CARS.

>> Reporter: BUDDY CALDWELL OF LOUISIANA BELIEVE IT TOO.

PREPARING A LAWSUIT.

LOUISIANA FILED CLAIMING STATE FARM'S PRACTICE IS PUTTING DRIVERS IN DANGER.

AND WHAT IS THE PRACTICE? WHAT'S BEING PUT IN THEIR CARS? >> AFTERMARKET PARTS, JUNK YARD PARTS AND ALL OF THIS WITHOUT ANY COMMUNICATION WITH THE CONSUMER AND THAT'S THE MAIN ISSUE, THE SAFETY ISSUES AND THE KNOWLEDGE THAT THEIR PRODUCT IS BEING DEVALUED BY THE PRACTICES OF THE INSURANCE COMPANY.

I MEAN, BUDDY HAS FOUND NUMEROUS CASES HERE IN LOUISIANA.

WE FOUND IN MISSISSIPPI, THE BODY SHOPS, PUT JUNK PARTS AND WELD THE PATCH.

>> Reporter: WHEN AUTO SHOPS DON'T GO ALONG, MISSISSIPPI'S ATTORNEY GENERAL SAID THOSE AUTO SHOPS BUSINESS GETS CUT.

IT'S CALLED STEERING.

INSURANCE COMPANIES STEERING BUSINESS ELSEWHERE.

>> THEY'RE GOING TO SAY, WE'LL BLACKBALL YOU.

WE WON'T PUT YOU ON OUR SELECT SERVICE LIST AND WE'RE GOING TO MAKE YOU SEND ESTIMATESTOUS TO FIVE TIMES.

>> Reporter: U.

S.

SENATOR RICHARD BLOOMEN THAT WILL WHO USED TO BE CONNECTICUT'S ATTORNEY GENERAL NOT ONLY THE POTENTIAL FOR SMALL BUSINESS TO BE HURT BUT BELIEVE CARS REPAIRED THROUGH THE PREFERRED SERVICE CENTERS PROPOSE A SAFETY RISK AND ASKED THE U.

S.

DEPARTMENT OF JUSTICE TO INVESTIGATE.

>> SALVAGE PARTS INFERIOR OR EVEN COUNTERFEIT PARTS RAISE SAFETY CONCERNS AND OFTEN, THOSE KIND OF PARTS INVOLVED IN THE PRACTICE OF STEERING AND THAT'S WHY I HAVE BEEN CONCERNED FOR YEARS ABOUT IT.

AND WHY I THINK THE DEPARTMENT OF JUSTICE SHOULD BE INVESTIGATING.

>> Reporter: LOUISIANA'S ATTORNEY GENERAL CHOSE STATE FARM BECAUSE THEY'RE THE BIGGEST INSURER IN HIS STATE AND LEGAL FILINGS, THE COMPANY DENIES ALL THE ALLEGATIONS INCLUDING THE ALLEGATION THAT STATE FARM MANDATES USING AFTERMARKET PARTS.

STATE FARM WOULD NOT GRANT INTERVIEW BUT SENT A STATEMENT INSTEAD.

IT SAID OUR CUSTOMERS CHOOSE WHERE THEIR VEHICLES ARE GOING TO BE REPAIRED.

WE PROVIDE INFORMATION ABOUT OUR SELECT SERVICE PROGRAM WHILE AT THE SAME TIME MAKING IT CLEAR THEY CAN SELECT WHICH SHOP WILL DO THE WORK.

STATE FARM TOLD US TO BRING OUR SPECIFIC QUESTIONS TO NEIL OLRIDGE WITH THE NATIONAL ASSOCIATION OF MUTUAL INSURANCE COMPANIES.

>> IT'S NOT JUST IN THE ECONOMIC INTEREST OF THE INSURER TO HAVE A CAR GO IN AND OUT OF AN AUTO BODY SHOP FOUR OR FIVE TIMES TO GET IT RIGHT.

>> Reporter: WHY WOULD THEY RECOMMEND USED PARTS, FIXED PARTS OFF MARKET? >> SURE.

MOST COMPANIES DON'T REQUIRE THIS.

MOST COMPANIES OFFER A CHOICE TO CONSUMERS.

MOST OF THE ANY SORT OF AFTERMARKET PART YOU MIGHT HEAR ABOUT ARE USUALLY COSMETIC PARTS.

NOTHING RELATED TO THE SAFETY, THE MECHANICAL PARTS OF THE OPERATION OF THE VEHICLE.

THERE ARE LAWS IN ALMOST EVERY STATE THAT REQUIRE CONSUMERS TO BE TOLD THAT IF AFTERMARKET PARKTS ARE USED AND WHAT THEY ARE.

>> Reporter: WE FOUND THIS NOTICE ON PAGE FOUR OF THE ESTIMATE ON PAGE SIX OF THIS ONE.

>> IN MANY CASES, THESE PARTS ARE NO DIFFERENT.

THEY'RE MADE ON THE SAME FACTORIES.

ONE JUST COMES OUT WITH AN AUTO MANUFAC MANUFACTURER'S NAME ON IT AND OTHERS DON'T.

>> THAT'S NOT TRUE.

>> IT IS TRUE.

>> Reporter: IT CERTAINLY ISN'T TRUE IN THE CASE OF THIS REPLACEMENT HOOD FOR A HONDA MADE IN TAIWAN AND ALREADY COMING APART.

THIS AFTERMARKET BUMPER STRAIGHT OUT OF THE BOX NOT ONLY DOESN'T FIT BUT THE FASTENERS HAVE BEEN GLUED BACK TOGETHER AND THEN THERE'S THE QUESTION ABOUT THAT BROKEN AND REPAIRED TOYOTA TACOMA HEAD LAMP.

>> IT'S OBVIOUSLY A REPURPOSED PART FROM A JUNK YARD AND IF YOU LOOK CLOSELY, YOU'LL SEE HOW IT WAS GLUED TOGETHER, SNAPPED TOGETHER AND IN SOME CASES, EVEN WELDED AND SCREWED TOGETHER AND THIS IS WHAT THE INSURER TOLD THE PREFERRED BODY SHOP TO PUT ON THE CAR.

LOOK AT THIS.

YOU WOULDN'T WANT THAT IN YOUR CAR, I WOULDN'T WANT THAT IN MY CAR.

>> I DON'T KNOW THE CIRCUMSTANCES OF THE PICTURE, SO I REALLY CAN'T COMMENT ON IT.

>> Reporter: SO ARE THE ATTORNEY GENERALS WRONG IN SAYING THAT THE INSURANCE INDUSTRY AS A WHOLE, STATE FARM IN PARTICULAR, IS STEERING THEIR CUSTOMERS TO PREFERRED BODY SHOPS, PREFERRED BECAUSE THEY SAVE THE INSURANCE COMPANY MONEY, NOT THE CONSUMER? >> THE INSURANCE COMPANY MAY PROVIDE A LIST OF AUTO BODY SHOPS.

AND THE CUSTOMER CAN SAY NO, I WANT TO GO TO JOE'S BODY SHOP AROUND THE CORNER AND THAT'S THE CHOICE.

>> Reporter: THAT'S WHAT PROGRESSIVE INSURANCE TOLD US HAPPENED FOR THIS CAR.

REMEMBER, IT'S THE CAR WE TOLD YOU ABOUT EARLIER WITH THE RIP TAIL FRAME THAT YOU COULD ONLY SPOT WITH THE BOROSCOPE.

ONLY HIT FROM BEHIND.

A PREFERRED BODY SHOP AND SENT BACK ON THE ROAD WITH A RIPPED AND HIDDEN TAIL FRAME.

TURNS OUT IT WASN'T OLD, NOT REPAIRED.

THREE OF FOUR TIRE RIMS ARE DAMAGED AND THE UNDERCARRIAGE OF THE CAR IS PUSHED IN ACCORDING TO AUTO EXPERT BILL BURN AND OUTSIDE, THE PAINT JOB IS FILLED WITH POCKMARKS.

PROGRESSIVE INSURANCE SAY THEY DIDN'T CHOOSE THE BODY SHOP, THE OWNER DID.

WELL, THIS IS THE OWNER.

EUG EUGENEA RANDALL WHO NEEDS THE CAR TO CARRY HER 2-YEAR-OLD SON ROMAN AND REMEMBERS THE CONVERSATION WITH PROGRESSIVE MUCH DIFFERENTLY.

>> THEY DIDN'T GIVE ME A CHOICE AS TO WHERE I WANTED TO TAKE IT.

THEY JUST TOLD ME TO TAKE IT TO THEIR PREFERRED SHOP.

>> Reporter: RANDLE SAID BECAUSE IT WAS A PREFERRED SHOP, IT WOULD BE REPAIRED TO A HIGHER STANDARD BUT WHEN SHE PICKED IT UP, SHE IMMEDIATELY KNEW SOMETHING WASN'T RIGHT.

>> COSMETICALLY TO ME IT LOOKED FINE BUT ONCE I GOT IN AND GOT DOWN THE STREET, IT JUST STARTED DRIVING REALLY CRAZY AND I IMMEDIATELY TOOK IT BACK.

>> Reporter: SO HOW CRAZY WAS RANDLE'S CAR DRIVING? I DECIDED TO FIND OUT FOR MYSELF BY GETTING BEHIND THE WHEEL.

>> ANYTHING OVER 50 MILES PER HOUR, THIS THING JUST SHAKES.

THIS THING IS REALLY SHAKING NOW.

>> Reporter: NOT ONLY THE TAIL SECTION RIPPED AN UNREPAIRED, THREE OF FOUR TIRE RIMS DAMAGED AND AS I DROVE, THE STEERING WHEEL SHAKING SO VIOLENTLY, I HAD TO GRIP DOWN FROM VEERING TO THE RIGHT.

THE FRONT LEFT TIRE WAS JUST WOBBLING.

I CAREFULLY DROVE THIS SHAKING CAR RIGHT BACK TO THE INSURANCE COMPANY'S PREFERRED AUTO BODY SHOP.

WHERE THE GENERAL MANAGER PROMPTLY TOLD US TO LEAVE.

>> DON'T TURN THAT ON WITHOUT THE SERVICE PERMISSION IF YOU DON'T MIND.

>> Reporter: AS FOR THE SHAKING CAR, THE INSURANCE COMPANY EVENTUALLY DECLARED IT A TOTAL LOSS GIVING HER FULL REPLACEMENT VALUE.

BUT ONLY AFTER SHE HIRED AN ATTORNEY AND CNN BEGAN INVESTIGATING THIS STORY.

>> THE VEHICLE SPUN OUT.

>> UNBELIEVABLE.

DREW GRIFFIN JOINING US NOW.

I HAD NO IDEA ABOUT THIS WHOLE PLAN THEY HAVE.

DID THE REPAIR COMPANY THAT SUPPOSEDLY FIXED THE SHAKING CAR EVER GIVE AN EXPLANATION? >> Reporter: THE COMPANY SERVICE KING SAID THEY DID WHAT THE INSURANCE COMPANY APPROVED AND SAID ALL THEIR REPAIRS COME WITH A WRITTEN LIFETIME WARRANTY.

SERVICE KING'S CORPORATE OFFICE SAID IT WAS UNAWARE THERE WERE PROBLEMS OR COMPLAINTS AND.

What Is An Auto Body Shop?

>> I'm Chad.

I'm a second-year student here at DCTC.

I've been an apprentice at ABRA inBloomington for just about a year, now.

Doing some frame damage,here, repair on a 2005 Ford.

>> Focus.

>> Focus.

Three door, got hit here,and this here was the main impact.

We've already cut the reinforcementand impact bar off.

Now, we're going to be pulling onthis frame here, to get it straight, using the three-dimensionalmeasurement system to make sure that everything else is inline where it should be.

>> I'm Gerry Rainford.

I'm a second-year instructor here,at Dakota County Technical College.

Chad's a typical second-year student, wherewe get into different levels of repair needs, from just simple door repair to, well, you cansee here, is a full unibody reconstruction.

Mechanical aspects, as well.

Getting into the air conditioning andother mechanical systems on the vehicle.

Suspension, driveline.

This is kind of the way that once we havethe vehicle anchored on our frame rack.

We come through and we can actually do pull out.

We're going to be doing a light pull,this morning on the unibody structure.

We're going to see if we can't repair the rails.

Typically, when they're kinked to thispoint, we would do a replacement procedure.

But we're going to see ifwe can't repair them, today.

So, we'll just kind of talk as we go through it.

And we'll see if we can getthe rails to come out.

So, Chad, please take over from here.

>> All right.

I'm going to be using these towers, here, thatare capable of pulling 10,000 pounds apiece.

Try to get this mash come outon this left frame rail, here.

>> So, once again.

Keep pulling.

We're going to be pulling at a constantlevel that's going to be straight out, to try to replace the height, thelength, and width of the rail.

So, we're going to keep the directionstraight and at a straight pulling distance.

>> And all I'm doing here, now, is justwatching as I'm pulling, going slowly to find out how the metal's going to react.

Everything reacts different,not any accident is the same.

Everything needs to be takenon with a different viewpoint.

What I'm going to do now, isjust hit this metal, here, to try to relieve some of this stress.

[ Hammering Sound ] And always while you're pulling,what you're going to want to do is check your anchoring points, again, tomake sure that the car is not going anywhere.

Make sure all your chainsand clamps are still tight.

As you'll notice, I'm staying above,not standing behind these chains, just in case anything would happen to let go.

[ Hammering Sound ] >> Let's work the backside of the railthrough here a little bit, as well.

[ Hammering Sound ] [inaudible] target.

One of the things we don't want to do, is we don't want to do additionaldamage as we're pulling.

Looks like we're pulling morefrom the bottom of the rail.

>> Yeah.

>> Than we are from the top.

So, at this point in time, I think we shouldstop, rehook, and grab a hold of the top of the clamp support and pullmore on the top of this rail.

>> All right.

Both these dozers here are run by the same pump.

So, as I pull it's going to pull them equally.

>> Okay.

Let's get some pressure on there.

[ Inaudible Comments ] [ Hammering Sound ] >> Just trying to relieve this stress.

Move the metal where I want it.

>> So, let's get a couple ofhits with this on the backside.

[ Hammering Sound ] Right now, we're concernedwith overpulling on it.

And so, I think we're going to stop.

And we're going to regrab ontothe rail at a different location.

Once you've overpulled and it distortsthe rail, then we've got an issue.

>> We're going to cut this outsideof this rail, here off, this cap.

Just a piece of the sheet seal,here, out of high strength steel.

We're going to pull this out here, sothat way we can get inside here, too, and make proper welds and getthis metal straight, again.

I'm just going to be countered along,drill out these spot welds, here.

And then, cut it here at the seam.

I'll run a line, section it out.

>> Why don't you show them how we know how farwe need to pull by using the measuring system? Then, to explain the measuringsystem, real quick? >> All right.

As we pull out on this stuff here, toget this rail out to where it should be, these targets here measure with this beamunderneath the vehicle, measures the vehicle at all kinds of different points.

Four in the middle of the vehicle, twoat the rear of the vehicle, and then, these here in the front closest to the damage.

This vehicle, this chart here for thevehicle is specific for this vehicle.

What this does here, is it hangs targets fromthe vehicle at specific manufacturing locations.

It measures the vehicle throughout there.

You can tell that our centersection here, is good.

And the back of the vehicle is good.

But up here, we're dealing with offmeasurements on the front end from the impact.

>> We're going to take and when we getthe rails pulled back into a location by the manufacturer's specifications, we'lltake, we'll hammer and dolly all this straight.

And we'll take, we've got new components.

We've got a new reinforcement barthat we'll be welding into place, to replace the structure of the vehicle.

But we'll come through, replace the.

You want to come around over here.

You can see that the radiator condenserhas been damaged in this accident.

And it's completely, we've lost all the Freon.

So, we'll be doing an R and Rprocedure on the condenser assembly.

Then, we're going to evac andrecharge the air conditioning system.

And then, move forward with the restof the mechanical repairs at this time.

In some situations, when you getcomposite intake manifolds, like this, components can come back and dodamage to the intake manifolds, starters, alternators, AC compressors.

We have additional damage deeper in the vehicle.

And this one, we've simplygot a condenser to replace.

What's so, how long will ittake you to do this repair? >> This repair here, will take me probablyabout two weeks to finish, to complete.

Done quite a bit already.

Already had all my parts ordered.

Those have already been checkedin and identified, and made sure that they are the rightparts, so I'm not scrambling at the end of the project to find the correct parts.

I'd say about two weeks; two to three weekswould be a good timeline for this vehicle.

>> Well, thank you, Chad.

I appreciate it, taking your time withthe students and this is what we do here at Dakota County Technical College.

It's a two-year program.

We try to get you ready with the latesttechnology and the latest equipment to make sure that they're ready for the industry.

And so, they can be productive and profitablein today's unibody reconstruction world.

Thanks, very much.