Summit Auto Body | Peotters Tire and Auto

For the majority of drivers, going to an auto body shop in Summit is a mysterious experience, a scary encounter with the unknown.

Once you hand over your key, you instantly feel uneasy; will your car be returned as good as new, or will the repair specialists do a shoddy job?

How will you know? How will you be able to figure out if you hard-earned money is just being tossed down the drain?

Auto Bodies

The best way to know if you are receiving excellent service and professional care is to find a reputable Summit Auto Body shop and then build a relationship with that shop.

However, most people who take their vehicles in to the Auto Body Shop are doing so for the first time. So, how do you know whether or not you can trust an auto body shop?

First of all, it is important to know that most auto body shops are reputable businesses. The majority of Summit Auto Body owners are just struggling to make a living like most small business owners – they want to do a great job on your car so you will return or refer others to their shop.

Auto Repair

However, there are a few bad apples that spoil the whole bunch, and you need to be diligent when selecting a shop.

The first thing to do is get a referral or locate a shop online using reviews and testimonials.

>> I'm Chad.

I'm a second-year student here at DCTC.

I've been an apprentice at ABRA inBloomington for just about a year, now.

Doing some frame damage,here, repair on a 2005 Ford.

>> Focus.

>> Focus.

Three door, got hit here,and this here was the main impact.

We've already cut the reinforcementand impact bar off.

Now, we're going to be pulling onthis frame here, to get it straight, using the three-dimensionalmeasurement system to make sure that everything else is inline where it should be.

>> I'm Gerry Rainford.

I'm a second-year instructor here,at Dakota County Technical College.

Chad's a typical second-year student, wherewe get into different levels of repair needs, from just simple door repair to, well, you cansee here, is a full unibody reconstruction.

Mechanical aspects, as well.

Getting into the air conditioning andother mechanical systems on the vehicle.

Suspension, driveline.

This is kind of the way that once we havethe vehicle anchored on our frame rack.

We come through and we can actually do pull out.

We're going to be doing a light pull,this morning on the unibody structure.

We're going to see if we can't repair the rails.

Typically, when they're kinked to thispoint, we would do a replacement procedure.

But we're going to see ifwe can't repair them, today.

So, we'll just kind of talk as we go through it.

And we'll see if we can getthe rails to come out.

So, Chad, please take over from here.

>> All right.

I'm going to be using these towers, here, thatare capable of pulling 10,000 pounds apiece.

Try to get this mash come outon this left frame rail, here.

>> So, once again.

Keep pulling.

We're going to be pulling at a constantlevel that's going to be straight out, to try to replace the height, thelength, and width of the rail.

So, we're going to keep the directionstraight and at a straight pulling distance.

>> And all I'm doing here, now, is justwatching as I'm pulling, going slowly to find out how the metal's going to react.

Everything reacts different,not any accident is the same.

Everything needs to be takenon with a different viewpoint.

What I'm going to do now, isjust hit this metal, here, to try to relieve some of this stress.

[ Hammering Sound ] And always while you're pulling,what you're going to want to do is check your anchoring points, again, tomake sure that the car is not going anywhere.

Make sure all your chainsand clamps are still tight.

As you'll notice, I'm staying above,not standing behind these chains, just in case anything would happen to let go.

[ Hammering Sound ] >> Let's work the backside of the railthrough here a little bit, as well.

[ Hammering Sound ] [inaudible] target.

One of the things we don't want to do, is we don't want to do additionaldamage as we're pulling.

Looks like we're pulling morefrom the bottom of the rail.

>> Yeah.

>> Than we are from the top.

So, at this point in time, I think we shouldstop, rehook, and grab a hold of the top of the clamp support and pullmore on the top of this rail.

>> All right.

Both these dozers here are run by the same pump.

So, as I pull it's going to pull them equally.

>> Okay.

Let's get some pressure on there.

[ Inaudible Comments ] [ Hammering Sound ] >> Just trying to relieve this stress.

Move the metal where I want it.

>> So, let's get a couple ofhits with this on the backside.

[ Hammering Sound ] Right now, we're concernedwith overpulling on it.

And so, I think we're going to stop.

And we're going to regrab ontothe rail at a different location.

Once you've overpulled and it distortsthe rail, then we've got an issue.

>> We're going to cut this outsideof this rail, here off, this cap.

Just a piece of the sheet seal,here, out of high strength steel.

We're going to pull this out here, sothat way we can get inside here, too, and make proper welds and getthis metal straight, again.

I'm just going to be countered along,drill out these spot welds, here.

And then, cut it here at the seam.

I'll run a line, section it out.

>> Why don't you show them how we know how farwe need to pull by using the measuring system? Then, to explain the measuringsystem, real quick? >> All right.

As we pull out on this stuff here, toget this rail out to where it should be, these targets here measure with this beamunderneath the vehicle, measures the vehicle at all kinds of different points.

Four in the middle of the vehicle, twoat the rear of the vehicle, and then, these here in the front closest to the damage.

This vehicle, this chart here for thevehicle is specific for this vehicle.

What this does here, is it hangs targets fromthe vehicle at specific manufacturing locations.

It measures the vehicle throughout there.

You can tell that our centersection here, is good.

And the back of the vehicle is good.

But up here, we're dealing with offmeasurements on the front end from the impact.

>> We're going to take and when we getthe rails pulled back into a location by the manufacturer's specifications, we'lltake, we'll hammer and dolly all this straight.

And we'll take, we've got new components.

We've got a new reinforcement barthat we'll be welding into place, to replace the structure of the vehicle.

But we'll come through, replace the.

You want to come around over here.

You can see that the radiator condenserhas been damaged in this accident.

And it's completely, we've lost all the Freon.

So, we'll be doing an R and Rprocedure on the condenser assembly.

Then, we're going to evac andrecharge the air conditioning system.

And then, move forward with the restof the mechanical repairs at this time.

In some situations, when you getcomposite intake manifolds, like this, components can come back and dodamage to the intake manifolds, starters, alternators, AC compressors.

We have additional damage deeper in the vehicle.

And this one, we've simplygot a condenser to replace.

What's so, how long will ittake you to do this repair? >> This repair here, will take me probablyabout two weeks to finish, to complete.

Done quite a bit already.

Already had all my parts ordered.

Those have already been checkedin and identified, and made sure that they are the rightparts, so I'm not scrambling at the end of the project to find the correct parts.

I'd say about two weeks; two to three weekswould be a good timeline for this vehicle.

>> Well, thank you, Chad.

I appreciate it, taking your time withthe students and this is what we do here at Dakota County Technical College.

It's a two-year program.

We try to get you ready with the latesttechnology and the latest equipment to make sure that they're ready for the industry.

And so, they can be productive and profitablein today's unibody reconstruction world.

Thanks, very much.

Create a list and call each shop to see how well you are treated on the phone.

Select three or four shops that sound good and are in close proximity to your location, and you are ready to take your vehicle in for an estimate.

You should get at least three estimates from three different shops.

The estimate may vary because Auto Body Shops may use different estimating software, but they should all be in the same ballpark. If an estimate differs by a great deal, you should ask why.

The body shop expert should be able to explain all prices on the estimate, including all price quotes and labor charges.

When you get the estimate, you should also be evaluating the Auto Body customer service:

How quickly were you acknowledged?

How efficiently were you helped?

Were all members of the staff polite and friendly?

Did the staff seem knowledgeable?

Be observant during the estimate and you will have a good idea of how you will be treated during the entire repair process.

If the customer service seems lacking, move on to the next place even if the estimate seems reasonable.

If you decide to leave your car, and the shop contacts you later to tell you about additional charges, this may be a sign that it is not a reputable and honest repair facility.

Collision Auto Repair

Though additional charges can happen occasionally, it is not a common practice for a reputable shop.

If you do your homework, have some patience, and get a few estimate, the odds are good that you will find a reputable auto body shop.

Once you have found one, it helps to direct all your business to them, and refer them to others.

If you do this, you will have established a good relationship, and you will no longer need to worry about finding an honest auto body shop.

The Results Are In – Who Do You Think is the Best Summit Auto Body in the Area?

Auto Mechanic Services

Today's vehicles are made with many different types of fuel-saving materials like lightweight alloys and plastics. It is important for an auto body shop to be aware of the different materials and techniques used for repairing them.

Auto body shops and collision repair services refer to manuals for instructions repairing bumpers. The different material types require various finish materials, removal and installation procedures.

Bumper Repairs

When a plastic bumper is cracked or has a small hole it can be repaired to look as good as new. Replacing the bumper is wasteful and it creates unnecessary debris for our landfills. A good, eco-friendly auto body shop will only recommend replacing the bumper if the damage is severe enough that repair time would be considered unreasonable and quality of results would be unsatisfactory.

The cost of repairing small abrasions, cracks and holes in plastic bumpers is often much cheaper than replacing the part. Of course, many collision repair technicians would rather replace the part and charge a fee for their labor plus mark-up on the price of the part because they lack in cosmetic repair skills and it is easier to warranty the work.

Working with Plastics

The first step to repairing plastic bumpers is to identify the material in order to choose the method of repair. Auto body shops use ISO codes on the parts to identify the various families of plastics. They cross-reference the codes with charts from the suppliers or by accessing reference materials on the internet.

It is important that the collision repair technician determine the type of plastic they are working with so they know the proper welding procedure to use to avoid damage to the part.

Some plastics can be welded with an airless welder or hot-air welder; others require a hot glue type of procedure. Tests must be performed and welding procedures have to be done correctly to avoid adhesion failure. Some bumpers will melt with a slight color change and they will remain tacky in the area where they have melted.

Adhesive Repairs

The bumper repair technician must identify the type of plastic they are working with in order to be successful with adhesive repairs. Failure to properly identify the plastic results in adhesion-related problems.

Flexibility

Some repair materials are based on flexible and rigid plastics. Using the wrong material can cause cracking when the part is flexed or it may not provide the correct strength for the repair area.

Cleaning and Prep

Proper cleaning and prep is critical for proper adhesion and finish. Whether the technician is repairing or replacing the bumper, the part will need to be cleaned. The bumper being repaired is likely to be dirty from the road; the new replacement part can have contamination on it from the manufacturing process.

Auto body repair professionals should use a low-VOC surface cleaner or a special plastics parts cleaner to help prevent solvents from going too deep into the plastic. If solvents are too harsh, they go deep into the plastic and cause adhesion problems after repairs are done.

This is an overview of the process of working with plastics. Time is money in the auto body industry; therefore, many collision repair technicians choose to replace rather than repair plastic bumpers and other parts.

Technology allows us to repair many items that are often replaced. As resources become scarce and landfills become over-full, we really should consider repairing rather than replacing when possible.

How to Pick the Right Auto Body Repair Shops

Automotive Shop

(upbeat music) - Hey, this is Donnie Smith.

Have you ever overground metal, making it too weak and too thin? Well it's not that hard to do with these thinner metals.

What about when working with body filler? Have you ever gotten it in cracks, gaps, other placesthat you don't want it? Takes quite a bit of time to get that out of there and clean it up.

So if you'd like to learn some tricks, how to prevent over-thinning your metal when working with thin metal, and how to keep fromgetting all the body filler in the places you don'twant it in the first place, then you're in luck, because that's what we'regonna show you in this video.

Alright, let's just goahead and get started.

What we're gonna do to eliminate grinding a lot of the metal off,is to use a DA Sander, and we can use 36 grit, or 80.

I'm using 80 here.

That usually works well.

May take just a little bit longer to remove the paint coatings, but you're not gonna chancegrinding too much metal off.

This does not take the amountof metal that grinding does.

Now with thinner metals,I would recommend this.

Now if you're working on older vehicles, grinding may be a little quicker, and that may still work fine.

Okay, now for the tip of how to eliminate getting body filler in places you don't want it, and that's simply to mask it off.

On the edge, I don't want the body filler wrapping around the edgewhere I have to clean it up, so I'm gonna mask that off.

Any gaps, for instance here, there's a, where the molding goes, I don't want body filler to wrap in there where I'm gonna have to sand it out, so I'm gonna use the bodylines that's on the car, and use that as a dividing line to make nice, sharp lines at, so that the body fillerdoes not get in these areas.

(upbeat music) Okay, now I'm mixing thebody filler up in the tube.

I'm gonna let the air out of the cap, so that it'll mix well.

And once I remove some of the air, I'll put the cap back on, and now I'm just gonnamix it inside the tube, because this hardener reallydoes separate a lot in there.

If you don't do this, you'll have liquid-ysubstance that comes out, and you don't want that, so be sure that you mixit up well in the tube before you use it.

Now I've already got somebody filler out here, and I used a paint stick toput some on this mixing board.

And I'm gonna get this hardener, I'm gonna apply a stripfrom edge of the body filler to the other, and that usually is a pretty good mixing ratio.

And notice I'm using a spreader to mix it.

I'm not using a paint stick to stir it, because that could put air bubbles in it.

If you get air bubblesin your body filler, that's gonna create pinholes, whenever you go to sanding body filler.

So it's always best towork the air bubbles out.

Just spread it out on your filler until it's nice and uniform.

You don't want there tobe any hardener streaks.

You wanna mix it until it's one color.

(upbeat music) Okay, now I have the filler mixed good.

It's nice, uniform, one color.

We don't have any hardener streaks in it, so we know that it's mixed well.

I'm gonna apply the body filler.

Now to do this, I'm gonnaapply a tight coat first, and what that is, iswhere I take a thin coat of body filler, and push really hard down on the spreader, so thatI push it into the metal.

That helps it adhere better to the metal, so that you don't have any problems with adhesion at a later point.

Now once I get the tight coat on, I come back with a fill coat, and that's where I'm gonnaput a little bit less pressure on the spreader, which allows it to fill the damaged area in.

(upbeat music) Okay I have the fill coat applied.

Now here's a tip for you to eliminate a lot of the sanding, and that is to work on your edges, because if you have real hard edges, it's gonna take more sanding.

So what I'm doing here, is I'm using the spreader, and on the edges I'm kind of feathering that body filler out, so that edge is a real thin layer, and you don't have that big, hard edge to try to sand out.

Okay, now let this setup for just a little bit, and you don't want to do it immediately after you apply the body filler.

You wanna let the filler set, but you don't want it to be dry either.

But as it's kind of in its green state, go ahead and pull the tape off.

This will leave you nice clean edges.

And also before it fully cures, you can block sand lightly, you don't wanna sand too hard, just to help level someof the highs and lows.

Okay, now I allow it to dry, and started block sanding it.

Now I'm starting out with 36 grit, because that's gonna levelthe filler really fast, but notice that I'mstaying within the filler.

My block is not slidingout onto the paint, because I don't want those deep scratches getting onto the paint surface.

I'm just wanting to level the filler.

(upbeat music) Also notice that I'm sandingin different directions.

I'm not just going at oneangle the entire time.

So I change it up.

And what sanding indifferent directions does, is it's gonna help youget a more level surface.

So always sand in different directions.

(upbeat music) (sanding) (upbeat music) Once you have it level, switch to 80 grit.

That's what I'm doing here.

First, I'm gonna apply some guide coat, and this just to helpidentify highs and lows, and you'll know whenever you get rid of the 36 grit scratches.

Makes it easier to see this way.

Now also notice I am sandingout on the paint a little bit.

I'm not going too far, but you do wanna sand out further than you did with your 36 grit.

You wanna make sure all 36 grit scratches are removed during this step.

(upbeat music) Okay I finished blocking, and I'm feeling for high areas.

And usually if you seemetal spot areas like this, that's gonna indicate that it is high.

And that happens sometimes, and if it does, what you need to do is get your pick hammer, and lightly tap down on those metal areas.

And what this is gonna do, is it's gonna lower that metal.

(upbeat music) And here's another tip for you.

If you're having problemsfilling the bodywork, and determining highs and lows with your hand, with your bare hand, use something like this, a wipe all, or a towel or somethingto put between the panel and your hand.

And this may help you be able to feel the highs andthe lows much better.

Now I'm gonna use the tape, because I'm gonna be applying some putty, so I'm gonna do the same thingI did with the body filler, the edges, and that indention where the body side molding goes.

I'm gonna tape all that off, to keep all the filler out of that.

Now when using putty, it lays out a littlethinner than body filler, so I usually just go halfway, rather than from one edgeof the filler to the other.

So I'm gonna do about halfthe amount of hardener.

(upbeat music) But everything else is basically the same.

Mix it until it's one uniform color.

Don't want any streaks in there.

And the good thing aboutputty is it's thinner, and it's easier to get a nice skim coat, but you do wanna do the tight coat, followed by a fill coat.

And another thing about a putty, is you can go over the entire repair area, from paint edge to paint edge, and that helps any imperfections you had in your sanding flaws, or sanding scratches,or anything like that, it's gonna fill in.

(upbeat music) And after allowing it tosetup for a few minutes, now I'm gonna peel the tape.

(upbeat music) Now when sanding finish putty, I'm not gonna start out with 36 grit.

I'm gonna start out withthe 80 to level it out.

And also I wanna let it fully dry.

I really don't wanna try to sand putty in its green state, so I'llallow it to dry all the way.

Then I'm gonna get 80 on a block, and I'm gonna sand it.

And I'm gonna cross sand it.

Make sure it's good and level.

(upbeat music) Once I have it leveled with 80, I'm gonna use the guide coat, and then I'm gonna comeback with 150 to 180.

I'm using 150 here I believe, but anywhere between 180and 150 will work fine for smoothing out your 80 grit scratches.

And this guide coat, it will help you identify any lows that you may have if there are any, or let you know whenever you got all the 80 grit scratches sanded out.

(upbeat music) And one last thing you wanna do, before you send it offto start priming it, you wanna make sure it fits.

Make sure everything aligns.

Make sure that your body work is right.

So you're gonna have toput it up to the car, and make sure everything works.

(upbeat music) Always, thanks for watching this video.

Be sure and share it with your friends.

Give us a thumbs up, a like, and be sure to subscribe to our channel.

Also be sure to go to CollisionBlast.

Com.

And there we have hours of free autobody and painttraining videos like this one, and a lot of other resources for you.

Thanks again for watching.

Have a safe and productive week, and we'll see you in the next video.

(upbeat music).

Repair Automotive

New Jersey Auto Body Shop | Peotters Tire and Auto